Skip to Content

Changes for page 8. Control Setup Manual

Last modified by Iaroslav Platonov on 2026/06/09 11:18
From version 7.6
edited by Lana
on 2025/12/17 19:38
Change comment: There is no comment for this version
To version 5.1
edited by Lana
on 2025/12/17 19:32
Change comment: Uploaded new attachment "Screenshot 2025-12-17 at 16.31.55.png", version {1}

Summary

Details

Page properties
Content
... ... @@ -1,6 +1,6 @@
1 -= CONTENT =
1 +CONTENT
2 2  
3 -= 1. INTRODUCTION =
3 +~1. INTRODUCTION
4 4  
5 5  CENTO is a multifunctional software platform for data acquisition, processing and display. This manual describes how to configure the CENTO user tool Control.
6 6  
... ... @@ -8,9 +8,9 @@
8 8  
9 9  This manual describes how to configure the Control service, which is used to send control commands to the objects being controlled.
10 10  
11 -= 2. CONTROL USING WEB INTERFACE =
11 +2. CONTROL USING WEB INTERFACE
12 12  
13 -== 2.1. Control using the device, tags editor ==
13 +2.1. Control using the device, tags editor
14 14  
15 15  A user with the appropriate permissions can control the object using the devices, tags, channels editor.
16 16  
... ... @@ -36,48 +36,4 @@
36 36  
37 37  To proceed, enter the account password. After successful authentication, a modal window appears allowing to specify the value to be written to the device (see Fig. 2.4).
38 38  
39 -[[image:Screenshot 2025-12-17 at 16.31.55.png]]
40 -
41 -Figure 2.4. Entering value for control
42 -
43 -After entering the value in the field, click **Send** (see Fig. 2.4).
44 -
45 -Next, confirm the entered value by clicking **Execute** to initiate the control command and write the value to the device. Alternatively, click **Cancel,** to cancel the operation (see Fig. 2.5).
46 -
47 -[[image:Screenshot 2025-12-17 at 16.32.27.png]]
48 -
49 -Figure 2.5. Confirmation of the command to write a value
50 -
51 -Clicking **TC** also opens a password prompt window. After successful authentication, a command selection window appears (see Fig. 2.6). As with the Control, a confirmation window follows the selected command.
52 -
53 -[[image:Screenshot 2025-12-17 at 16.33.06.png]]
54 -
55 -Figure 2.6. Selecting command for remote control
56 -
57 -= 3. SETTING CONTROL =
58 -
59 -== 3.1. Setting using WEB interface ==
60 -
61 -Setting control for tags transmitted via Modbus, OPC DA, or IEC-104 protocols is performed through the **Edit parameter** interface located under Settings > Devices, tags, channels, in the **Tags, channels** tab. In this interface, select the target device in the device tree by checking the box next to it. The device should be configured with one of the supported protocols: Modbus TCP, Modbus RTU over TCP, OPC DA, or IEC-104. To open the tag editing interface, click on the tag identifier or tag name in the general tag list.
62 -
63 -The interface includes protocol-dependent fields:
64 -
65 -- general settings described in the “Setup manual”,
66 -
67 -- reading settings as defined in the relevant configuration manuals,
68 -
69 -- settings for writing:
70 -
71 -* Remote control (discrete signal transmission to the device) for IEC-104 protocol: "Remote control is allowed", "Select before operate (SBO)", "Function", "Command duration", "Switch on address", "Switch on value", "Switch off address", "Switch off value", for Modbus TCP protocol: "Remote control is allowed", "Function", "Value length", "Switch on address", "Switch on value", "Switch off value", "Switch off address", "Write by bitmask";
72 -* Control (transmission of a positive integer to the device) for Modbus TCP protocol: "Record values", "Function", "Data type in device", "Address", "Byte order", conversion elements: "Physical value (lower limit)", "Physical value (upper limit)", "Value to record (lower limit)", "Value to record (upper limit)", for OPC DA protocol: "Record values", "Device Tag Data Type", conversion elements: "Physical value (lower limit)", "Physical value (upper limit)", "Value to record (lower limit)", "Value to record (upper limit)".
73 -
74 -
75 -1) The remote //control// function is available for Modbus TCP Modbus RTU over TCP) protocols (see Fig. 3.1.1) and IEC 104 (see Fig. 3.1.2).
76 -
77 -The position of the **Remote control is allowed **switch determines whether record commands can be sent to the device at the specified address.
78 -
79 -The position of the **Select before operate (SBO)** switch defines whether command selection is required prior to executing telecontrol commands.
80 -
81 -In the Remote **control **field, select the appropriate ASDU type for the control command from the drop-down list (see Fig. 3.1.4).
82 -
83 83  
Screenshot 2025-12-17 at 16.32.27.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Lana
Size
... ... @@ -1,1 +1,0 @@
1 -134.2 KB
Content
Screenshot 2025-12-17 at 16.33.06.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Lana
Size
... ... @@ -1,1 +1,0 @@
1 -100.7 KB
Content