Skip to Content

Changes for page 8. Control Setup Manual

Last modified by Iaroslav Platonov on 2026/06/09 11:18
From version 7.4
edited by Lana
on 2025/12/17 19:35
Change comment: There is no comment for this version
To version 4.2
edited by Lana
on 2025/12/17 19:30
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -31,39 +31,3 @@
31 31  Clicking **C** opens a pop-up window prompting the user to enter a password to access the control function (see Fig. 2.3).
32 32  
33 33  [[image:Screenshot 2025-12-17 at 16.30.01.png]]
34 -
35 -Figure 2.3. Entering password
36 -
37 -To proceed, enter the account password. After successful authentication, a modal window appears allowing to specify the value to be written to the device (see Fig. 2.4).
38 -
39 -[[image:Screenshot 2025-12-17 at 16.31.55.png]]
40 -
41 -Figure 2.4. Entering value for control
42 -
43 -After entering the value in the field, click **Send** (see Fig. 2.4).
44 -
45 -Next, confirm the entered value by clicking **Execute** to initiate the control command and write the value to the device. Alternatively, click **Cancel,** to cancel the operation (see Fig. 2.5).
46 -
47 -[[image:Screenshot 2025-12-17 at 16.32.27.png]]
48 -
49 -Figure 2.5. Confirmation of the command to write a value
50 -
51 -Clicking **TC** also opens a password prompt window. After successful authentication, a command selection window appears (see Fig. 2.6). As with the Control, a confirmation window follows the selected command.
52 -
53 -[[image:Screenshot 2025-12-17 at 16.33.06.png]]
54 -
55 -Figure 2.6. Selecting command for remote control
56 -
57 -3. SETTING CONTROL
58 -
59 -3.1. Setting using WEB interface
60 -
61 -Setting control for tags transmitted via Modbus, OPC DA, or IEC-104 protocols is performed through the **Edit parameter** interface located under Settings > Devices, tags, channels, in the **Tags, channels** tab. In this interface, select the target device in the device tree by checking the box next to it. The device should be configured with one of the supported protocols: Modbus TCP, Modbus RTU over TCP, OPC DA, or IEC-104. To open the tag editing interface, click on the tag identifier or tag name in the general tag list.
62 -
63 -The interface includes protocol-dependent fields:
64 -
65 -- general settings described in the “Setup manual”,
66 -
67 -- reading settings as defined in the relevant configuration manuals,
68 -
69 -- settings for writing:
Screenshot 2025-12-17 at 16.31.55.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Lana
Size
... ... @@ -1,1 +1,0 @@
1 -131.6 KB
Content
Screenshot 2025-12-17 at 16.32.27.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Lana
Size
... ... @@ -1,1 +1,0 @@
1 -134.2 KB
Content
Screenshot 2025-12-17 at 16.33.06.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Lana
Size
... ... @@ -1,1 +1,0 @@
1 -100.7 KB
Content