Skip to Content

Changes for page 8. Control Setup Manual

Last modified by Iaroslav Platonov on 2026/06/09 11:18
From version 42.1
edited by Lana
on 2025/12/17 20:32
Change comment: Uploaded new attachment "Screenshot 2025-12-17 at 17.32.18.png", version {1}
To version 45.2
edited by Lana
on 2025/12/17 20:36
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -347,5 +347,35 @@
347 347  
348 348  Next, for the object with remote control commands, this attribute, should be enabled as shown in Fig. 3.3.19, and the command sending on the diagram should be tested.
349 349  
350 +[[image:Screenshot 2025-12-17 at 17.32.18.png]]
350 350  
352 +Figure 3.3.19. Configuring object for control without entering password
353 +
354 +=== 3.3.2. Configuring permission for remote control ===
355 +
356 +Before executing remote control commands, some devices require an initial permission signal to be sent to a dedicated register. This signal enables remote control functionality. Only after this permission is granted the device accepts and process the main remote control commands.
357 +
358 +To implement this type of remote control (TC) in CENTO, the following attributes are added to the object class (see Fig. 3.3.20):
359 +
360 +* **telecontrol_permit_on_ti** – permission to switch TC on;
361 +* **telecontrol_permit_off_ti** – permission to switch TC off.
362 +
363 +[[image:Screenshot 2025-12-17 at 17.34.12.png]]
364 +
365 +Figure 3.3.20. Attributes for remote control permission
366 +
367 +The system assigns the IDs of the corresponding tags to these attributes of the IM object. These tags are configured to send a signal to the register that enables remote control (see Fig. 3.3.21)
368 +
369 +[[image:Screenshot 2025-12-17 at 17.34.50.png]]
370 +
371 +Figure 3.3.21. Configuration of attributes for enabling telecontrol
372 +
373 +When an object uses the system class //Telecontrol// to send control commands, the permission-related attributes are designated as //permit_on_tag// and //permit_off_tag// (see Fig. 3.3.22):
374 +
375 +[[image:Screenshot 2025-12-17 at 17.35.21.png]]
376 +
377 +Figure 3.3.22. Attributes for enabling remote control
378 +
379 +In some devices, a single tag handles this function, while in others, two separate tags perform it. These tags are configured similarly to those used for direct remote control, differing only in the register address (see Fig. 3.3.23):
380 +
351 351  
Screenshot 2025-12-17 at 17.34.12.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Lana
Size
... ... @@ -1,0 +1,1 @@
1 +116.5 KB
Content
Screenshot 2025-12-17 at 17.34.50.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Lana
Size
... ... @@ -1,0 +1,1 @@
1 +74.6 KB
Content
Screenshot 2025-12-17 at 17.35.21.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Lana
Size
... ... @@ -1,0 +1,1 @@
1 +107.1 KB
Content