Skip to Content

Changes for page 8. Control Setup Manual

Last modified by Iaroslav Platonov on 2026/06/09 11:18
From version 4.1
edited by Lana
on 2025/12/17 19:30
Change comment: Uploaded new attachment "Screenshot 2025-12-17 at 16.30.01.png", version {1}
To version 7.4
edited by Lana
on 2025/12/17 19:35
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -20,4 +20,50 @@
20 20  
21 21  **C** is an abbreviation for //Control//. **TC** is an abbreviation for //Telecontrol.// In CENTO software, //Control// refers to sending a non-negative integer value to a device, while //Telecontrol //refers to sending a discrete signal.
22 22  
23 -
23 +[[image:Screenshot 2025-12-17 at 16.28.40.png]]
24 +
25 +Figure 2.1. Tags with telecontrol enabled
26 +
27 +[[image:Screenshot 2025-12-17 at 16.29.26.png]]
28 +
29 +Figure 2.2. Tags with control and telecontrol enabled
30 +
31 +Clicking **C** opens a pop-up window prompting the user to enter a password to access the control function (see Fig. 2.3).
32 +
33 +[[image:Screenshot 2025-12-17 at 16.30.01.png]]
34 +
35 +Figure 2.3. Entering password
36 +
37 +To proceed, enter the account password. After successful authentication, a modal window appears allowing to specify the value to be written to the device (see Fig. 2.4).
38 +
39 +[[image:Screenshot 2025-12-17 at 16.31.55.png]]
40 +
41 +Figure 2.4. Entering value for control
42 +
43 +After entering the value in the field, click **Send** (see Fig. 2.4).
44 +
45 +Next, confirm the entered value by clicking **Execute** to initiate the control command and write the value to the device. Alternatively, click **Cancel,** to cancel the operation (see Fig. 2.5).
46 +
47 +[[image:Screenshot 2025-12-17 at 16.32.27.png]]
48 +
49 +Figure 2.5. Confirmation of the command to write a value
50 +
51 +Clicking **TC** also opens a password prompt window. After successful authentication, a command selection window appears (see Fig. 2.6). As with the Control, a confirmation window follows the selected command.
52 +
53 +[[image:Screenshot 2025-12-17 at 16.33.06.png]]
54 +
55 +Figure 2.6. Selecting command for remote control
56 +
57 +3. SETTING CONTROL
58 +
59 +3.1. Setting using WEB interface
60 +
61 +Setting control for tags transmitted via Modbus, OPC DA, or IEC-104 protocols is performed through the **Edit parameter** interface located under Settings > Devices, tags, channels, in the **Tags, channels** tab. In this interface, select the target device in the device tree by checking the box next to it. The device should be configured with one of the supported protocols: Modbus TCP, Modbus RTU over TCP, OPC DA, or IEC-104. To open the tag editing interface, click on the tag identifier or tag name in the general tag list.
62 +
63 +The interface includes protocol-dependent fields:
64 +
65 +- general settings described in the “Setup manual”,
66 +
67 +- reading settings as defined in the relevant configuration manuals,
68 +
69 +- settings for writing:
Screenshot 2025-12-17 at 16.31.55.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Lana
Size
... ... @@ -1,0 +1,1 @@
1 +131.6 KB
Content
Screenshot 2025-12-17 at 16.32.27.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Lana
Size
... ... @@ -1,0 +1,1 @@
1 +134.2 KB
Content
Screenshot 2025-12-17 at 16.33.06.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Lana
Size
... ... @@ -1,0 +1,1 @@
1 +100.7 KB
Content