Skip to Content

Changes for page 8. Control Setup Manual

Last modified by Iaroslav Platonov on 2026/06/09 11:18
From version 39.1
edited by Lana
on 2025/12/17 20:25
Change comment: Uploaded new attachment "Screenshot 2025-12-17 at 17.25.19.png", version {1}
To version 43.1
edited by Lana
on 2025/12/17 20:34
Change comment: Uploaded new attachment "Screenshot 2025-12-17 at 17.34.12.png", version {1}

Summary

Details

Page properties
Content
... ... @@ -325,8 +325,39 @@
325 325  
326 326  3.3.1. Setting up control and remote control without password
327 327  
328 -In standard operation, sending control and telecontrol signals requires user password entry. However, in certain cases, this level of security may be excessive. To accommodate such scenarios, the CENTO software includes a setting that allows //Control without password.//
328 +In standard operation, sending control and remote control signals requires user password entry. However, in certain cases, this level of security may be excessive. To accommodate such scenarios, the CENTO software includes a setting that allows //Control without password.//
329 329  
330 330  Control without password is configured using the diagram (i.e., via the Information Model). To enable this, add the attribute Control without password with the code //skip_password// and the bool type to the class of the control object (see Fig. 3.3.16).
331 331  
332 +[[image:Screenshot 2025-12-17 at 17.25.19.png]]
333 +
334 +Figure 3.3.16. Setting the control attribute without entering password
335 +
336 +Thus, when creating an object of the selected class (see Fig. 3.3.17), include the specified attribute in the value field and verify its functionality on the diagram.
337 +
338 +[[image:Screenshot 2025-12-17 at 17.27.04.png]]
339 +
340 +Figure 3.3.17. Configuring an object with control without entering password
341 +
342 +To skip password entry during remote control, as with control, an attribute named //Skip password// (any name can be used) is to be added. This attribute should have the  //skip_password// code and the //bool// type(see Fig. 3.3.18).
343 +
344 +[[image:Screenshot 2025-12-17 at 17.27.52.png]]
345 +
346 +Figure 3.3.18. Configuring the attribute for password-free control
347 +
348 +Next, for the object with remote control commands, this attribute, should be enabled as shown in Fig. 3.3.19, and the command sending on the diagram should be tested.
349 +
350 +[[image:Screenshot 2025-12-17 at 17.32.18.png]]
351 +
352 +Figure 3.3.19. Configuring object for control without entering password
353 +
354 +=== 3.3.2. Configuring permission for remote control ===
355 +
356 +Before executing control commands, some devices require an initial permission signal to be sent to a dedicated register. This signal enables telecontrol functionality. Only after this permission is granted the device accepts and process the main telecontrol commands.
357 +
358 +To implement this type of telecontrol (TC) in CENTO, the following attributes are added to the object class (see Fig. 3.3.20):
359 +
360 +* **telecontrol_permit_on_ti** – permission to switch TC on;
361 +* **telecontrol_permit_off_ti** – permission to switch TC off.
362 +
332 332  
Screenshot 2025-12-17 at 17.27.04.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Lana
Size
... ... @@ -1,0 +1,1 @@
1 +106.1 KB
Content
Screenshot 2025-12-17 at 17.27.52.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Lana
Size
... ... @@ -1,0 +1,1 @@
1 +111.9 KB
Content
Screenshot 2025-12-17 at 17.32.18.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Lana
Size
... ... @@ -1,0 +1,1 @@
1 +121.9 KB
Content
Screenshot 2025-12-17 at 17.34.12.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Lana
Size
... ... @@ -1,0 +1,1 @@
1 +116.5 KB
Content