Skip to Content

Changes for page 8. Control Setup Manual

Last modified by Iaroslav Platonov on 2026/06/09 11:18
From version 14.1
edited by Lana
on 2025/12/17 19:44
Change comment: Uploaded new attachment "Screenshot 2025-12-17 at 16.43.58.png", version {1}
To version 10.1
edited by Lana
on 2025/12/17 19:40
Change comment: Uploaded new attachment "Screenshot 2025-12-17 at 16.40.14.png", version {1}

Summary

Details

Page properties
Content
... ... @@ -106,34 +106,4 @@
106 106  
107 107  The **Write by bitmask **field specifies the mask in decimal, binary, or HEX format.
108 108  
109 -2) The //Control// function is available for Modbus TCP (Modbus RTU over TCP) protocols (see Fig. 3.1.3 ), and OPC DA (see Fig. 3.1.9).
110 -
111 -[[image:Screenshot 2025-12-17 at 16.40.14.png]]
112 -
113 -Figure 3.1.3. Setting  control for Modbus protocol
114 -
115 -[[image:Screenshot 2025-12-17 at 16.41.11.png]]
116 -
117 -Figure 3.1.4. Remote control for IEC-104
118 -
119 -Settings for writing: Write values, Function, Device Tag Data Type, Address, Byte order; Tranformation elements: Physical value (lower limit), Physical value (upper limit), Record value (lower limit), Record value (upper limit).
120 -
121 -The position of the **Write values** switch determines whether value write commands can be sent to the device at the specified address.
122 -
123 -The **Function** field selects the Modbus recording function from the drop-down list (see Fig. 3.1.5).
124 -
125 -[[image:Screenshot 2025-12-17 at 16.41.51.png]]
126 -
127 -Figure 3.1.5. Modbus control function
128 -
129 -FC5 (0x05) - recording the value of one flag (Force Single Coil).
130 -
131 -FC16 (0x10) - recording multiple registers, used to write a block of contiguous registers (1 to 123 registers) to a remote device (Write multiple registers).
132 -
133 -The **Address** field specifies the address of the tag in the device memory to which the value will be written. The address should be a non-negative integer in decimal format.
134 -
135 -The field **Byte order** from the drop-down list (see Fig. 3.1.6) is used to select different order of bytes and/or words in the written CENTO data.
136 -
137 -[[image:Screenshot 2025-12-17 at 16.42.23.png]]
138 -
139 -In the **Device Tag Data Type** field, select the data type used by the device to store values from the drop-down list (see the device manual for details) (see Fig. 3.1.7).
109 +2) The
Screenshot 2025-12-17 at 16.41.11.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Lana
Size
... ... @@ -1,1 +1,0 @@
1 -67.9 KB
Content
Screenshot 2025-12-17 at 16.41.51.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Lana
Size
... ... @@ -1,1 +1,0 @@
1 -12.4 KB
Content
Screenshot 2025-12-17 at 16.42.23.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Lana
Size
... ... @@ -1,1 +1,0 @@
1 -32.3 KB
Content
Screenshot 2025-12-17 at 16.43.58.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Lana
Size
... ... @@ -1,1 +1,0 @@
1 -32.6 KB
Content